Home  

Keep Your Home Warm During The Winter With A Manufactured Home Heat Pump


Heat pumps are without doubt an effective and efficient way to keep your home warm during the rather cold winter months. However, to avoid an outage after only some brief use, it is important to buy a heat pump that delivers years of cost saving service without the need to be replaced or even repaired. When choosing a heat pump for your manufactured home, there are certain factors one has to take into consideration.

To fully appreciate the factors one needs to consider, it is important to first understand how the unit functions. Just like an air conditioner, a heat pump does use refrigeration principles rather than fuel combustion to cool and heat. In cooling mode, the unit acts like an air conditioner by extracting heat from the indoors and expelling it outdoors. When switched to heating mode, the unit reverses the process by drawing heat from even the outdoors to warm the interior. In this regard, whether or not your pump saves you money on your bills depends on a variety of factors such as the type of fuel you are using, your climate as well as other energy efficiency features such as insulation that you have in your manufactured home.

To get the best unit, it is important to check your heat pump efficiency ratings. Generally, all cooling and heating appliances have a federal energy guide label that’s used to rate the efficiency levels for both heating and cooling mode of the unit in question. For cooling, manufacturers use two indexes; these are SEER (Seasonal Energy Efficiency Rating) for cooling purposes and the HSPF (Heating Seasonal Performance Factor) for heating purposes. Normally, the SEER does evaluate the overall efficiency of the heat pump when it is in the cooling mode. This ratio is usually based on the amount of cooling that’s generated, measured in BTUs and then divided by the amount of electricity used during the cooling season. Therefore, a higher SEER rating does indicate a more energy efficient unit.

In the U.S, the systems must have a minimum SEER reading of 13. When it comes to heating your home, then the HSPF rating comes in handy. The higher the HSPF rating, the more efficient the unit is bound to be. They also tend to have a higher price tag than those with slightly lower ratings even though this initial cost overhead can be recouped within a relatively short period of time.

It is also important to choose a pump that’s the correct size for your home. You should choose a unit that will adequately power your manufactured home without significantly affecting your utility bills. They are usually sized in tonnage. To determine the capacity that you will need in your home, you need to clearly determine the average cold weather temperature in your area and then compare it with the estimated capacity at that particular temperature range of the unit you have in mind. Getting the most appropriate size is very important because if you opt for a unit that’s too small for the home, it will constantly keep your home warm. On the other hand, if you choose a heat pump that’s too large, then the humidity in the air will all be taken up during the summer.

Here are some of the most common manufactured home heat pumps readily available in the market. They include but are not limited to the following:

1) Product Name: Friedrich 30,000 BTU Single Zone

Product Price: $ 2303.00

Product URL: http://is.gd/OvIxit

Product Details: the unit does treat up to 848 cubic feet of air per minute and cranks up about 30,000 BTUs of heating and cooling power. The unit does have an auto-changeover from cooling to heating. It does also have reusable and washable antimicrobial air filters.

2) Product Name: Goodman Heat Pump 16 SEER

Product Price: $ 1621.00

Product URL: http://is.gd/w78Ej6

Product Details: the unit has a R-410 A chlorine free refrigerant as well as a high density foam compressor sound blanket. It does also have a two stage scroll compressor as well as a heavy gauge galvanized steel cabinet with baked powder paint finish. The unit is also fitted with low and high pressure switches.

3) Product Name: Revolv 3 Ton Self Contained Heat Pump

Product Price: $ 2153.71

Product URL: http://is.gd/c9cV97

Product Details: this three ton, 13 SEER energy rating, the unit does implement state of the art compressor technology as well as an improved closed cell foam insulation. The unit does also have a powder coat finish that’s tested to 1000 hours of salt spray standard and used the environmentally friendly R410A cooling agent.  



Lynn Haven, Little Rock, Mattoon, Edmond, Ypsilanti, Pineville, Northglenn, Laurinburg, Lebanon, Antioch, Rock Hill, San Luis Obispo, Guam, Carrollton, Independence, Quincy, Miamisburg, South Elgin, Pasadena, Portales, Kansas, Lawrenceville, Van Wert, Calexico, Pleasantville, Novato, LaGrange, Gillette, Katy, Great Falls, North Arlington, Bay Village, Arkansas, North Carolina, Westminster, Stow, Canyon, Mississippi, Orem, Oroville, Terre Haute, Morro Bay, Elk River, Blacksburg, Hinsdale, Cuyahoga Falls, Leominster, Agoura Hills, Lincoln Park, Lawton, Michigan City, Kinston, Dixon, East Cleveland, Hialeah Gardens, Guttenberg, Batavia, Kiryas Joel, Bethel Park municipality, Dobbs Ferry, Allouez, Hopkins, Decatur, New Castle, Thornton, Wauwatosa, Oakdale, Warren, La Ca??ada Flintridge, Juneau and, Elk City, Boone, Orlando, Auburn, The Colony, Hereford, California, Crestwood, Morgan Hill, Westminster, Defiance, Maryville, Waco, Williston, Arlington, Rhode_Island, Dublin, Hutchinson, Nevada, Florida, Englewood, River Grove, Naples, Farragut, District of Columbia